A coil of guitar string and a tuning fork resting on a wooden desk beside a closed notebook, in warm lamplight

The waves formulas a physics course relies on fit on one short sheet: v = fλ, the speed of a wave on a string, the speed of sound, standing-wave frequencies for strings and pipes, and sound intensity level in decibels. What makes them usable is the condition attached to each, especially that wave speed is set by the medium.

The general physics formula sheet gives waves two lines, and for good reason: two relationships carry most of an introductory treatment. This sheet goes one layer deeper, into the formulas that appear once a course reaches sound and standing waves, and keeps the rule that every entry names what it needs before the equation appears.

What sets the speed of a wave?

The medium, not the source. That is the condition behind every other line on this sheet, and it is the one most often lost.

OpenStax puts it in general terms: the speed of a mechanical wave depends on the square root of an elastic property of the medium divided by an inertial property. For sound in air it adds a second fact that matters for problems: the speed of sound is nearly independent of frequency, at least in open air across the audible range. High notes and low notes from the same band arrive together.

So when a problem changes the frequency of a source but keeps the medium the same, the speed stays fixed and the wavelength changes to compensate.

v = fλ: when does it apply, and what does it really say?

It applies to any periodic wave. OpenStax states that the velocity of any wave is related to its frequency and wavelength by v = fλ, and the period is T = 1/f. The wave speed equation page works it in detail.

Read it with the condition from the previous section. Since v belongs to the medium, v = fλ is really a statement about how λ responds to f. A 440 Hz tone in air at 20 °C, where sound travels at 343 m/s, has

λ = v / f = 343 m/s / 440 Hz = 0.780 m.

The same 440 Hz tone in fresh water, where OpenStax’s table lists the speed of sound as 1480 m/s, has λ = 1480 m/s / 440 Hz = 3.36 m. The frequency stayed at 440 Hz because the source set it. The speed changed because the medium changed, and the wavelength followed.

What is the speed of a wave on a string?

v = √(F_T / μ), where F_T is the tension and μ is the linear mass density, the mass per unit length in kg/m. OpenStax gives this for a pulse or wave on a string under tension. The condition is a uniform string under constant tension; the formula does not involve the frequency at all.

Take a string with μ = 5.0 × 10⁻³ kg/m under 80 N of tension:

v = √(80 N / 5.0 × 10⁻³ kg/m) = √(16,000 m²/s²) = 126.5 m/s, or about 130 m/s to the two significant figures the data support; the unrounded value is carried into the harmonics below.

The units work because N/(kg/m) = (kg·m/s²)(m/kg) = m²/s². Doubling the tension to 160 N raises the speed by a factor of √2, to √(32,000) = 179 m/s, not by a factor of 2. That square root is the answer to a common multiple-choice question.

What frequencies can a string fixed at both ends play?

Only those that fit a whole number of half-wavelengths into its length. With both ends fixed, OpenStax gives

λₙ = 2L / n and fₙ = n·v / (2L) = n·f₁, for n = 1, 2, 3, …

The condition is two fixed ends, which forces a node at each. All whole-number harmonics are allowed.

Continuing the example, if that string is 0.65 m long, its fundamental is f₁ = v / (2L) = 126.5 m/s / (2 × 0.65 m) = 126.5 / 1.30 Hz = 97.3 Hz, and the next harmonics are 2 × 97.3 = 195 Hz and 3 × 97.3 = 292 Hz. The sound in the air around the string has the same frequency as the string, as OpenStax notes, but a different wavelength, because it travels at the speed of sound rather than at about 130 m/s.

How do open and closed pipes differ?

In which harmonics they allow, and this is where the conditions do real work.

Pipe open at both ends. fₙ = n·v / (2L), for n = 1, 2, 3, … All harmonics, the same pattern as a string with both ends fixed.

Pipe closed at one end. fₙ = n·v / (4L), for n = 1, 3, 5, … Odd harmonics only, because the closed end must be a displacement node and the open end an antinode.

Both formulas come from OpenStax’s section on standing sound waves, and both need the speed of sound for the air inside, which depends on temperature. For a 0.50 m pipe with v = 343 m/s:

Open at both ends: f₁ = 343 m/s / (2 × 0.50 m) = 343 Hz, then 686 Hz, 1029 Hz.

Closed at one end: f₁ = 343 m/s / (4 × 0.50 m) = 171.5 Hz, then 3 × 171.5 = 514.5 Hz and 5 × 171.5 = 857.5 Hz.

Closing one end halves the fundamental and removes every even harmonic. A problem that lists 171.5 Hz and 343 Hz as neighboring resonances of the same pipe is describing an open pipe of a different length, not this closed one.

How does temperature change the speed of sound?

Through the square root of absolute temperature. OpenStax gives the approximation v ≈ 331 m/s × √(T / 273 K) for air, with T in kelvin. The condition is the kelvin scale: put in a Celsius value and the formula breaks, the same trap that catches the ideal gas law.

At 20 °C, T = 293.15 K, so v ≈ 331 m/s × √(293.15 / 273) = 331 m/s × 1.036 = 343 m/s. That matches the values OpenStax quotes directly: 331 m/s at 0 °C and 343 m/s at 20 °C, an increase of less than 4 percent. Small, but since every pipe formula contains v, the resonant frequencies of a pipe shift by the same percentage.

What is the decibel formula, and why is it a logarithm?

β = 10 log₁₀(I / I₀), in decibels, with I₀ = 10⁻¹² W/m². OpenStax defines I₀ as a reference intensity at the threshold of hearing for a person with normal hearing, and notes that pain begins around 1 W/m². The logarithm compresses that twelve-power-of-ten range into 0 to 120 dB.

A sound of intensity 1.0 × 10⁻⁵ W/m² has

β = 10 log₁₀(1.0 × 10⁻⁵ / 1.0 × 10⁻¹²) = 10 log₁₀(10⁷) = 10 × 7 = 70 dB.

The condition that matters here is that intensities combine by addition, while decibel levels do not. Double the intensity to 2.0 × 10⁻⁵ W/m² and the level becomes 10 log₁₀(2 × 10⁷) = 73.0 dB, an increase of 10 log₁₀ 2 = 3.01 dB, not a doubling to 140 dB. Every factor of 10 in intensity adds exactly 10 dB.

What about light?

Light follows v = fλ too, with the speed set by the medium through the index of refraction, and the key relationship for a first course is Snell’s law. Its page carries the condition that matters most, which is that the critical angle exists only going from a higher index to a lower one. The AP Physics 1 formula sheet walkthrough covers the one wave-like topic that course does include, simple harmonic motion, along with the small-angle condition on the pendulum period.

How should you use a waves sheet on a problem?

Identify the medium first, then the boundary conditions, then the formula. Medium tells you the speed. Boundary conditions (two fixed ends, open pipe, closed pipe) tell you which harmonics are allowed. Only then does a line from the sheet apply. The problem-solving method puts the principle before the equation for exactly this reason.

If a waves problem keeps coming out wrong by a factor of two, the boundary condition is the usual suspect, and it is a good problem to bring to Electra. Photograph it, and it names the medium and the boundary conditions, picks the formula that matches, and shows the arithmetic line by line so you can see which assumption your attempt made differently.

The rest of the formulas, each with its conditions and a worked example, are on the physics formulas page.

Sources